POLLUX 9 + STROBE WITH LIGHT POSITION WHITE/ORANGE
Description
The Pollux9+ Strobe is a further development of Ledson's immensely popular Pollux9+ Gen 2. The Pollux9+ Strobe also has an ECE R65 approved strobe light. This Stobe light consists of four powerful LEDs that can be set to five different flash patterns.
Flash Patterns:
- Single flash (ECE R65)
- Dual flash
- Triple flash
- Quadruple flash
- Continuous hyper flash
Synchronizable and with alternating flash pattern
Different Pollux9+ Strobe - lights can be synchronized with each other, meaning all lights use the same synchronized flash and strobe pattern. But you also have the option of an alternating flash pattern, which means your lights can be split into two different groups so they flash opposite each other. You can synchronize and use alternating flash patterns with an infinite number of lights, meaning there are no restrictions on the number of lights you use.
What is provided?:
- Pollux9+ Strobe Ledson LED 9" auxiliary light with road headlight and strobe function
- Pins and screws for fixing the light with one or two fixing points
- DT connector (6-pole, supplied with 2-pole adapter)
- Installation instructions
Installation instructions for cables (detailed instructions included with the product):
- Red: Auxiliary light (+)
- Black: Auxiliary light/ Positionsljus (- ground)
- Gray: Position light (+) white light
- Yellow: Position light (+) orange light
- Green: Strobe light (+)
- Blue: Pattern/Sync Strobe Light Switch
Strobe Pattern Synchronization: Connect the blue wires of two or more lights, then momentarily connect them to the positive terminal for 3 seconds to reset the strobe frequency on all connected lights, all flash patterns are changed.
NOTE: The DT connector must not be cut as this increases the risk of moisture damage and the warranty will become void.
Of course, the Pollux9+ Strobe is already equipped with a durable lens, but if you really care about the long life of your extra light, free from chips and scratches, we recommend our stone chip protectors. A cheap and easy way to give your new auxiliary light an extra layer of protection!
TIR reflectors
TIR stands for Total Inner Reflection and means that all light is effectively reflected and directed before being sent from the reflector. Spilled light (light that is not directed but disappears "out of focus" from the light without making any real use) is minimized. A traditional reflector directs and concentrates most of the light, but far from all of it.
Headlamp light pattern
The steering beam reflectors are all computer generated and manufactured to provide a light image similar to the combination, but more consistent and within the limits of what is legal. It imitates and enhances the truck's existing headlight and light image.
Installation:
- We strongly recommend using our DT relay with original connection to connect the LED bar to the vehicle.
Specifications:
- E marked (E8, ref. 37.5), ECE R112/R10/R7 (white position light)
- EMC safe (does not disturb the radio)
- With position light (4 LEDs) in orange or xenon white (connect the color you want)
- "Road headlight" light pattern
- Driving lamp range: 960 m (0.25 lux), 480 m (1 lux)
- 12000 lumens (theoretical), 9600 lumens (actual)
- Cool white light (6500 K)
- Pressure equalizing membrane
- 36 month warranty
Technical Data:
- 120 W (Cree XM-L2 LED 12 x 10 W)
- 4 pcs LED for strobe light
- Rated power 92.4 W
- IP68 (water/dust proof)
- 6-pole DT connector (2-pin adapter included)
- Electronic heat management
- Voltage 9-36 V
- Load 7.7 A @ 12 V and 3.6 A @ 24 V
Measurements:
- Width: 218 mm
- Height: 234.5 mm (including stand)
- Depth: 68.5 mm
- Weight: 1.9 kg
- Cable length: 650 mm
What is provided?:
- Pollux9+ Strobe Ledson 9" LED auxiliary light with high beam and strobe function
- Bolts and screws for fixing the luminaire with one or two fixing points
- DT connector (6 poles, supplied with 2 pole adapter)
- Installation instructions
Cable installation instructions (detailed instructions supplied with the product):
- Red: Auxiliary light (+)
- Black: Auxiliary light/ Positionsljus (- ground)
- Gray: Position light (+) white light
- Yellow: Position light (+) orange light
- Green: Strobe light (+)
- Blue: Pattern/sync strobe light switch
Strobe Pattern Synchronization: Connect the blue wires of two or more lights, then momentarily connect them to the positive terminal for 3 seconds to reset the strobe frequency on all connected lights, then all flash patterns are changed.
NOTE: The DT connector must not be cut as this increases the risk of moisture damage and the warranty is void.
